Checkline WT3-200 Manuel d'utilisateur

Model WT3-200 WIRE TERMINAL PULL TESTER User’s Guide CHECK•LINE®.ELECTROMATIC Equipment Co., Inc., 600 Oakland Ave., Cedarhu

Model WT3-200 Wire Terminal Pull Tester User’s Guide 9 Two filters are available: Current Reading – Applies to the peak capture rate of the ins

Model WT3-200 Wire Terminal Pull Tester User’s Guide 10When set points are enabled, the following indicators are shown to the left of the primary

Model WT3-200 Wire Terminal Pull Tester User’s Guide 11to the desired reading and press DELETE. The letter “D” will appear to the left of the rec

Model WT3-200 Wire Terminal Pull Tester User’s Guide 1210 COMMUNICATIONS Communication with the WT3-200 is achieved through the micro USB or 1

Model WT3-200 Wire Terminal Pull Tester User’s Guide 13 Restart the computer before connecting a Mark-10 USB device. 5. After Windows as restar

Model WT3-200 Wire Terminal Pull Tester User’s Guide 147. The next screen appears as follows: Click “Continue Anyway”. 8. The next, and fina

Model WT3-200 Wire Terminal Pull Tester User’s Guide 15 Data Bits: 8 Stop Bits: 1 Parity: None Other settings are configured as follows:

Model WT3-200 Wire Terminal Pull Tester User’s Guide 16 10.4 Break Detection Three functions can be triggered automatically upon sample break (b

Model WT3-200 Wire Terminal Pull Tester User’s Guide 17 10.4.2 Auto Output Settings Select the output type. One, both, or no output types may be

Model WT3-200 Wire Terminal Pull Tester User’s Guide 1810.7 I/O Connector Pin Diagram (DB-9HD-15 female) 11 CALIBRATION 11.1

Model WT3-200 Wire Terminal Pull Tester User’s Guide 1Thank you… Thank you for purchasing a Mark-10 WT3-200 wire terminal pull tester, designed

Model WT3-200 Wire Terminal Pull Tester User’s Guide 19The tester can be calibrated at up to 10 points. Enter the number of calibration points (a

Model WT3-200 Wire Terminal Pull Tester User’s Guide 20 Attach weight fixtures (brackets, hooks, etc), as required. Do not yet attach a

Model WT3-200 Wire Terminal Pull Tester User’s Guide 21 Use the UP and DOWN keys to adjust the load value as required. The load values default to

Model WT3-200 Wire Terminal Pull Tester User’s Guide 22 The entered calibration point is too close to the previous point. 12 PASSWORDS Two

Model WT3-200 Wire Terminal Pull Tester User’s Guide 2312.4 Password Prompts If passwords have been enabled, the following will be displayed whe

Model WT3-200 Wire Terminal Pull Tester User’s Guide 2413.2 Backlight Several initial settings are available upon powering on the tester. To acce

Model WT3-200 Wire Terminal Pull Tester User’s Guide 2513.5 Initial settings This section is used to configure the initial settings upon powerin

Model WT3-200 Wire Terminal Pull Tester User’s Guide 2614 SPECIFICATIONS 14.1 General Force Capacity: 200 x 0.1 lbF | 3200 x 2 ozF | 100 x

Model WT3-200 Wire Terminal Pull Tester User’s Guide 27 RS-232/USB Output Disabled Mitutoyo Output Disabled Automatic Storag

Model WT3-200 Wire Terminal Pull Tester User’s Guide 28 Mark-10 Corporation has

Model WT3-200 Wire Terminal Pull Tester User’s Guide 21 OVERVIEW 1.1 List of included items Qty. Part No. Description 1 08-1026 Battery (

Model WT3-200 Wire Terminal Pull Tester User’s Guide 32 POWER The tester is powered either by an 8.4V NiMH rechargeable battery or by an AC ad

Model WT3-200 Wire Terminal Pull Tester User’s Guide 43 SETUP 3.1 Assembly The lever is shipped disassembled from the unit to prevent damage i

Model WT3-200 Wire Terminal Pull Tester User’s Guide 5 5. When the test is complete, rotate the lever clockwise until the end of travel. T

Model WT3-200 Wire Terminal Pull Tester User’s Guide 64 HOME SCREEN AND CONTROLS 4.1 Home Screen No. Name Description 1 Tension

Model WT3-200 Wire Terminal Pull Tester User’s Guide 78 Battery / AC adapter indicator Either the AC adapter icon or battery power icon will be

Model WT3-200 Wire Terminal Pull Tester User’s Guide 85 OPERATING MODES Caution! In any operating mode, if the capacity of the tester has been