Checkline TT02 Manuel d'utilisateur

Series TT02 TORQUE TOOL TESTERS User’s Guide

Series TT02 Digital Torque Tool Testers User’s Guide 97 DIGITAL FILTERS Digital filters are provided to help smooth out the readings in situat

Series TT02 Digital Torque Tool Testers User’s Guide 10 Either one, two, or none of the set points may be enabled. To toggle between the clockwi

Series TT02 Digital Torque Tool Testers User’s Guide 11 9.1 View Data All the saved data points may be viewed. The record number is display

Series TT02 Digital Torque Tool Testers User’s Guide 12Note: Data is not retained while the tester is powered off. However, the tester protec

Series TT02 Digital Torque Tool Testers User’s Guide 1310.2.2 Data Format Select the desired data format. The screen appears as follows:

Series TT02 Digital Torque Tool Testers User’s Guide 1410.5 DATA Key Settings To configure the functions of the DATA key, select DATA Key fro

Series TT02 Digital Torque Tool Testers User’s Guide 15 Torque Pin function Both set points are CW Both set points are CCW CW upper set po

Series TT02 Digital Torque Tool Testers User’s Guide 1611.2 Settings Set up the trigger for auto output and storage, and the delay to zero th

Series TT02 Digital Torque Tool Testers User’s Guide 17 Any combination of the above functions may be selected. 12.2 Settings The display w

Series TT02 Digital Torque Tool Testers User’s Guide 18 11.3 Auto Output Settings Select the output type. Select RS-232/USB and/or Mitutoyo

Series TT02 Digital Torque Tool Testers User’s Guide 1Thank you… Thank you for purchasing a Mark-10 Series TT02 digital torque tool tester, des

Series TT02 Digital Torque Tool Testers User’s Guide 19example, Model MTT02-50 (with capacity of 50 lbFin) should be calibrated at 10, 20, 30

Series TT02 Digital Torque Tool Testers User’s Guide 20Attach weight fixtures (brackets, cable, hook, etc), as required. Do not yet attach any we

Series TT02 Digital Torque Tool Testers User’s Guide 2110. After all the clockwise calibration points have been completed, the display will appe

Series TT02 Digital Torque Tool Testers User’s Guide 22 The entered calibration point is too close to the previous point. 14 PASSWORDS Two

Series TT02 Digital Torque Tool Testers User’s Guide 23 Use the UP and DOWN keys to select the correct password, then press ENTER to continue.

Series TT02 Digital Torque Tool Testers User’s Guide 24 Select Off for the backlight to be off upon powering on the tester. Select On for the ba

Series TT02 Digital Torque Tool Testers User’s Guide 25 For available units, refer to the Units section. For available modes, refer to the H

Series TT02 Digital Torque Tool Testers User’s Guide 2616.2 Factory Settings Parameter SettingSet points Upper Disabled (defaults to

Series TT02 Digital Torque Tool Testers User’s Guide 2716.3 Capacity x Resolution Model No. ozFin lbFin lbFft Ncm NmMTT02-12 192 x 0.1 12 x

Series TT02 Digital Torque Tool Testers User’s Guide 21 OVERVIEW 1.1 List of included items Qty. Part No. Description 1 MTT02-12 / MTT02-5

Series TT02 Digital Torque Tool Testers User’s Guide 32 POWER The TT02 is powered either by an 8.4V NiMH rechargeable battery or by an AC adap

Series TT02 Digital Torque Tool Testers User’s Guide 43 SETUP Caution! Do not use Series TT02 torque testers with pneumatic or impact tools.

Series TT02 Digital Torque Tool Testers User’s Guide 53.3 Proper alignment Align the tool axially with respect to the square drive in the re

Series TT02 Digital Torque Tool Testers User’s Guide 64 HOME SCREEN AND CONTROLS 4.1 Home Screen No. Name Description 1

Series TT02 Digital Torque Tool Testers User’s Guide 7See Operating Modes section for details about each of these modes 7 Number of stored data

Series TT02 Digital Torque Tool Testers User’s Guide 85 OPERATING MODES Caution! In any operating mode, if the capacity of the instrument